loading

ford vehicles face u.s. safety probe over stalling, surging

DETROIT, MICH. —The U. S.
The National Highway Traffic Safety Administration says it will investigate nearly 725,000 Ford cars and SUVs that have turned off or their engines have soared.
The survey affected Ford Escape and Mercury Mariner SUVs, Ford Fusion and Mercury Milan cars from 2009 to 2011.
The agency said in a document published on its website on Monday that the vehicles may be willing to enter the \"lame home mode\" at a lower power \".
NHTSA and Ford have received nearly 1,500 complaints about the issue.
Three car accidents and injuries.
NHTSA began investigating cars and SUVs after receiving a request from the North Carolina Consumer Council last year. Non-
Interest safety groups and consumers can petition the agency to investigate the issue of vehicles.
The cars and SUVs have not yet been recalled, but the investigation could lead to the recall.
Fusion and Milan are almost the same cars, and the engine is the same as Escape and Mariner.
Ford abandoned the Mercury brand in 2010.
The organization in North Carolina says it has received two complaints about 2009 choking incidents diagnosed as stuck or closed.
The group said the owners reported that they had repeatedly delayed and soared.
Ford told NHTSA that cars produced from the month of June 22-10, 2009.
15, 09, there may be a printed circuit board failure to control the throttle.
Ford and its energy-saving supplier Delphi
After October, the circuit board manufacturing process was changed. 15, 2009.
NHTSA said in a document posted on its website on Monday that this solved the problem.
NHTSA said it analyzed 123 complaints about cars or SUVs entering the so-called lame mode, where the speed limit is 32.
Engine speed of 2 kilometers or 900 per minute.
Although the engine is still moving the vehicle, the driver may interpret the lame mode as flameout, the agency said.
When an engine problem is detected by the computer, the vehicle usually goes into lame mode.
This allows the driver to reach a safe place while protecting the engine from damage.
The agency said that when the engine speed fluctuates to prevent flameout in lame mode, there seems to be a surge in power.
But even though Ford says the throttle problem of escape has been solved as manufacturing changes, NHTSA still decides to investigate vehicles for 2010 and 2011 vehicle years.
The agency said it received 59 complaints about engine flameout and 2011 Fusion in 2010.
The agency said that from 2012, some of the complaints received were on the rise.
In addition, Ford also received 27,505 warranty claims for repair or replacement of the throttle body, NHTSA said.
Ford said Monday it was united.
Cooperate with NHTSA in the investigation.
Shares rose four cents to $12. 52 (U. S. )
In early trading on the New York Stock Exchange
They take 52-
The weekly range of $8. 82 to $14. 39.
For more car news, visit the wheels. ca.

GET IN TOUCH WITH Us
recommended articles
Knowledge Product case Info Center
Cx is a non-polar capacitor, and the IC integrated circuit module Ux is an IC (Integrated circuit components)
Kx is a component library of different manufacturers.
PCB thick transparent acrylic watch-
Plexiglass sheet aluminum grille, speaker, amplifier, battery, paint, PLEXIGLASS glue, screw Step 2: Prepare materials, warning: it is very important to use safety equipment, goggles and masks! !
Use the soldering iron and try to remove as much as possible from one side of the PCB board.
Objective: according to the requirements of engineering data MI, cut large sheets that meet the requirements into small pieces to produce plates.
Here are some obvious advantages for small batch PCB components of great value to manufacturers: cost advantage-
Although traditional economies of scale are known to have large output, low-capacity PCB production has significant cost advantages in changing technical schemes.
Industry-leading multi-layer circuit board processing and manufacturing technology procurement of top-level raw materials to create high-precision multi-layer PCB1 and top-level technical team for you, with rich production experience for precision multi-layer circuit boards ☆ all employees have 3-
Professional and technical personnel with 12 years of PCB experience, exquisite technology ☆ 8 industrial scientific and technological innovations, 20 PCB production technology innovations, effective o
If you still think that PCB design and technology are all tough guys who don't understand the amorous feelings, then let the following circuit board designs, which can be called works of art, subvert your concept.
Step 1: energize the circuit board.
Advantages and disadvantages are obvious: Advantages: low cost, smooth surface and good weldability (In the absence of oxidation).
Each winding circuit on the circuit board represents a different signal.
FPC in the process of production, in order to save costs, improve production efficiency, shorten the production cycle, production will have a puzzle way, rather than a single chip production.
Copyright © 2026 Rocket PCB Solution Ltd. |Privacy Policy Sitemap
Customer service
detect